We may earn a commission from some links on this page. Recommendations remain editorially independent.

Amazon hiring steps vary by role, location, business, and invitation. This page provides technical practice, not a claim that every maintenance technician candidate receives the same assessment. Any Mechatronics and Robotics Apprenticeship or technician process must be confirmed from the live role posting and invitation.

These are original technical questions for study. They are not Amazon, Ramsay, CAST, MAT-5, Wiesen, or apprenticeship test items. They do not provide live-electrical service instructions.

For additional timed practice after you review the official invitation and format notes below, Review JobTestPrep’s US Amazon Maintenance Technician Test preparation.

JobTestPrep is an independent third-party preparation provider. Confirm the current USD price, access period and included modules on the live product page before purchase.

Distinctions that matter

This technical guide is not an Amazon Area Manager Assessment guide. It is also separate from Ramsay Maintenance Test, Ramsay Electrical Test, MAT-5 mechanical aptitude, EEI CAST Test, and Wiesen Test of Mechanical Aptitude. An employer may use none, one, or another assessment, so confirm the assigned product.

Invitation-controlled formats

Amazon role titles, locations, business units, and hiring paths can differ. A maintenance or mechatronics candidate should not assume a universal online assessment, a particular Ramsay form, or a fixed set of technical topics. The job posting, recruiter communication, and assessment invitation are the reliable sources for the actual process.

Area Manager preparation is not a substitute for technician preparation. It emphasizes operations leadership, people management, and metrics rather than hands-on mechanical and electrical concepts. Ramsay assessments are also separate products. MAT-5 is an aptitude assessment, while maintenance and electrical forms can assess more applied knowledge. The Mechatronics and Robotics Apprenticeship path may have its own role-specific requirements, which should be verified from the current posting rather than inferred from technician content.

Technical study boundaries

Study principles, vocabulary, diagrams, and de-energized fault logic. Do not attempt live electrical work, defeat guards or sensors, reset protection repeatedly, or use a practice question as a service procedure. In a real workplace, site safety rules, lockout/tagout requirements, approved tools, and qualified personnel control the work.

Preparation plan

Review one system at a time: mechanical power transmission, basic electricity, motors and controls, sensors and PLC inputs/outputs, pneumatics, hydraulics, and preventive-maintenance documentation. Then use mixed sets to practice distinguishing symptoms from causes. A strong answer explains what is supported by the facts and what must be verified safely before any action.

30 original technical questions

  1. A loose drive belt most likely causes: A. slipping B. more torque C. lower friction always D. better alignment. Correct answer: A. Explanation: A loose belt can slip and reduce power transfer.
  2. A worn bearing can cause: A. vibration and heat B. more insulation C. zero friction D. higher voltage. Correct answer: A. Explanation: Wear increases friction and can create noise, heat, and vibration.
  3. 24 volts across 8 ohms produces: A. 2 A B. 3 A C. 8 A D. 192 A. Correct answer: B. Explanation: I = V/R = 24/8.
  4. A complete path for current is a: A. closed circuit B. open circuit C. pneumatic circuit D. bypass. Correct answer: A. Explanation: Current needs a complete path.
  5. A contactor commonly: A. switches power from a control signal B. measures length C. filters oil D. cuts threads. Correct answer: A. Explanation: A contactor switches a load circuit.
  6. A motor overload trips repeatedly. A possible cause is: A. excessive load B. clean ventilation C. no current D. correct rotation only. Correct answer: A. Explanation: Excess mechanical load can increase current.
  7. A clogged fluid filter usually: A. restricts flow B. increases flow C. creates voltage D. removes pressure loss. Correct answer: A. Explanation: Restriction reduces flow.
  8. Hydraulics use: A. liquid B. compressed air only C. gears only D. electricity only. Correct answer: A. Explanation: Hydraulic systems transmit force through liquid.
  9. Pneumatics use: A. compressed air or gas B. hydraulic oil only C. wood D. gravity. Correct answer: A. Explanation: Pneumatic systems use compressed gas.
  10. A pneumatic leak generally: A. reduces pressure B. raises pressure without limit C. increases flow D. lubricates bearings. Correct answer: A. Explanation: Escaping air reduces available pressure.
  11. A proximity sensor is commonly used to: A. detect an object’s presence B. measure pipe diameter only C. tighten bolts D. cool a motor. Correct answer: A. Explanation: It provides a position or presence signal.
  12. A photoelectric sensor commonly detects: A. a target using light B. liquid pressure C. voltage only D. gear ratio only. Correct answer: A. Explanation: It uses an emitted and received light signal.
  13. A PLC input receives: A. field information B. only mechanical torque C. hydraulic oil D. bearing grease. Correct answer: A. Explanation: Inputs bring sensor or switch states to the controller.
  14. A PLC output can command: A. an actuator B. a ruler C. a wrench D. a shaft key. Correct answer: A. Explanation: Outputs control devices such as relays or valves.
  15. A normally open contact is open when: A. unactuated B. overloaded C. lubricated D. energized in every case. Correct answer: A. Explanation: “Normal” is the resting state.
  16. A coupling joins: A. rotating shafts B. two wires only C. two hoses only D. two documents. Correct answer: A. Explanation: Couplings transmit rotation between shafts.
  17. Misaligned shafts often cause: A. vibration B. better bearing life C. less wear D. stronger insulation. Correct answer: A. Explanation: Misalignment loads components unevenly.
  18. A gearbox with a small driver and larger driven gear generally gives: A. lower speed and higher torque B. higher speed and lower torque C. no change D. no rotation. Correct answer: A. Explanation: The reduction increases torque.
  19. A fuse is intended to: A. open on excessive current B. supply air C. align belts D. store oil. Correct answer: A. Explanation: It is an overcurrent protective device.
  20. Corrosion at a terminal may: A. increase resistance B. eliminate voltage drop C. improve contact D. create a seal. Correct answer: A. Explanation: Corrosion impairs the connection.
  21. A lockout/tagout procedure helps prevent: A. unexpected energization B. normal documentation C. lubrication D. measurement. Correct answer: A. Explanation: It controls hazardous energy during authorized service.
  22. A machine stops after a sensor is blocked. First safe action is to: A. follow fault and safety procedure B. bypass the sensor C. force the output D. reach into the machine. Correct answer: A. Explanation: Do not defeat safeguards; use authorized troubleshooting.
  23. A seal-in contact is used to: A. hold a control circuit after a start input B. seal a pipe C. measure pressure D. slow a conveyor mechanically. Correct answer: A. Explanation: It maintains the control signal.
  24. A conveyor has intermittent movement and a loose terminal is found. The terminal may cause: A. intermittent operation B. permanent lubrication C. better contact D. lower resistance. Correct answer: A. Explanation: Poor connections can interrupt current.
  25. 120 V x 5 A equals: A. 24 W B. 115 W C. 600 W D. 1,200 W. Correct answer: C. Explanation: P = V x I.
  26. A regulator in an air system controls: A. pressure B. gear direction C. belt length D. wire color. Correct answer: A. Explanation: It sets downstream air pressure.
  27. A check valve permits flow: A. primarily one direction B. in every direction equally C. only electrically D. only when heated. Correct answer: A. Explanation: It prevents reverse flow.
  28. A preventive-maintenance task is intended to: A. reduce unexpected failure risk B. replace all repairs C. remove all inspections D. eliminate records. Correct answer: A. Explanation: Scheduled inspection and service help identify wear early.
  29. A work order should be closed with: A. accurate work and status documentation B. a guessed completion time C. no notes D. a deleted history. Correct answer: A. Explanation: Clear records support maintenance planning and traceability.
  30. The best source for your actual hiring format is: A. the employer invitation B. a generic forum C. an assumed cutoff D. a different job posting. Correct answer: A. Explanation: The invitation controls the process.